Menu

– MW range: up to 120 meters
– Separate outputs for alarm, disqualification and tamper
– Additional input for outdoor detectors
– RS485 connection to XTREAM and XSATHP
– USB connection directly to pc
– Complete management by pc via HPWIN software
– Alarms memory
– False alarm filter
– Consumption: 130 mA (TX+RX)
– Power supply: 220 Vac
– Dimensions (LxHxD): 136 x 225 x 225 mm
– Housing: plastic box with inside adjustment
HIGHER SECURITY
The security area is so width and height (up to 4 x 3 meters) that it is impossible to cross without generating an alarm and provides a higher security compared to other technologies.
LOWER FALSE ALARM RATE
Setting a pet immunity is easy: the alarm level is programmed to ignore small animals and generate less unwanted alarms.
INTEGRATION CIRCUIT
The security may be increased automatically thanks to its built-in integration circuit which amplifies the possible conditions for an alarm and triggers more easily.
DISQUALIFICATION
BM distinguish a real alarm from a disqualification situation (like a van parked between the barriers).
COMMON INTERFACE AND INSTALLATION
With the poles, BM are only 120cm high, it is easy and quick to install them, so the cost of installation is lower compared to other technologies. It is also simple to set perfectly thanks to few trimmers and dip-switches. Finally, thanks to its regular NC outputs, BM works with all alarm and CCTV systems.
MICROWAVE PLANAR ANTENNA
Since 2003, BM’s integrate planar antennas which reduce of 20% the sensibility area compared to former parabolic antennas. Longer distances BM can be installed for the same perimeters and costs are saved. In addition, to be protected from rain, the parabolic antennas use big expansive difficult-to-handle waterproof housings when the BM’s planar antennas are highly protected by tropicalisation and installed in high resistant protective cover to avoid the condensation and its consecutive rust development.
CLIMATIC ENVIRONMENT
BM operate in all weather conditions (snow, rain, fog) without distances reduction, unlike the active infrared barriers. If the temperature reaches less than -5°C, it is possible to place a TERM1 heating kit. BM temperature range is -20/+55°C.
POWER FEED
BM M and BM HP are 13.8 Vdc powered. VAC series is directly feed by the main (220Vac) and include an optional backup battery to compensate an electricity absence. Main power feeding simplifies the wiring and decrease the installation cost.
MARKETS
BM are perfect for all the perimeters: gardens, houses, borders, warehouses, airports, commercial resorts, car and truck parks, civilian, industrial, military, nuclear and electrical plants.
Maximum Range | 120 meters |
---|---|
Nominal Tension | 12V |
Minimum Tension | 11,5 V |
Maximum Tension | 15 V |
Standby Consumption | TX : 31 mA – RX : 100 mA |
Consumption During Alarm | TX : 31 mA – RX : 100 mA |
Dimensions (D x L x H) | 136 x 225 x 225 |
Block Input | Thought dedicated “B” input |
Additional Input | Negative input for detector |
Alarm Output | Normally closed exchange |
Disqualification Output | Normally closed output for information of disqualification |
Tamper Output | Normally closed exchange |
Optional Kit For Anti-Removal (AMP) | Yes |
Serial Output RS485 | yes |
Number of Selectable RS485 Addresses | Max 32 |
Events Memory | 3600 events memorized with curve, date, time, power |
Memorisation Stop At Disarmed System | yes |
False Alarm Filter | yes |
Test Point Output | For control of the signal received |
Microwave Working Frequency | 10.525 GHz (+/- 20MHz) |
Modulation | In 5 different channels, to select via dip-switch |
Irradiated RF Power | 25 dBm peak |
Working Temperature | From – 20°C to + 55°C |
IP Protection | IP 54 |
Equipped With | Bracket for fixation on 40 mm. pole |